    
--
-- Copyright (c) 2002 by EqualLogic, Inc.
-- 
-- All rights reserved.  This software may not be copied, disclosed,
-- transferred, or used except in accordance with a license granted
-- by EqualLogic, Inc.  This software embodies proprietary information
-- and trade secrets of EqualLogic, Inc.
--

   SCSI-MIB DEFINITIONS ::= BEGIN 
    
   IMPORTS 
     MODULE-IDENTITY, OBJECT-TYPE, NOTIFICATION-TYPE, 
     Integer32, Unsigned32, Counter32,  
     Counter64, Gauge32, 
     mib-2                                        FROM SNMPv2-SMI 
     TEXTUAL-CONVENTION, TimeStamp, TruthValue, 
     RowStatus, RowPointer, AutonomousType        FROM SNMPv2-TC 
     MODULE-COMPLIANCE, OBJECT-GROUP              FROM SNMPv2-CONF 
     SnmpAdminString                     FROM SNMP-FRAMEWORK-MIB; 
           
    
    
   scsiModule MODULE-IDENTITY 
     LAST-UPDATED "200202250000Z"         -- 25 February 2002 
     ORGANIZATION "IETF" 
     CONTACT-INFO " 
          Michele Hallak-Stamler 
 
          Sanrad Intelligent Network 
          32 Habarzel Street 
          Tel Aviv, Israel 
      
          Phone: +972 3 7674809 
          E-mail: michele@sanrad.com 
    
    
          Yaron Lederman 
          Siliquent Technologies Ltd. 
          33 Bezalel Street  
          Ramat Gan, Israel  
          
          Phone: +972 3 7552320 
          E-mail: yaronl@siliquent.com 
    
          Mark Bakke 
          Postal: Cisco Systems, Inc 
          6450 Wedgwood Road, Suite 130 
          Maple Grove, MN 
          USA 55311 
    
          Phone: +1 763-398-1000 
          Fax: +1 763-398-1001 
          E-mail: mbakke@cisco.com 
    
          Marjorie Krueger 
          Postal: Hewlett-Packard 
          Networked Storage Architecture 
          Networked Storage Solutions Org. 
          8000 Foothills Blvd. 
          Roseville, CA 95747 
    
          Phone: +1 916-785-2656 
          Phone: +1 916-785-0391 
          E-mail: marjorie_krueger@hp.com 
    
          Keith McCloghrie 
          Cisco Systems, Inc. 
          Postal: 170 West Tasman Drive 
          San Jose, CA USA 95134 
    
          Phone: +1 408 526-5260 
          E-mail: kzm@cisco.com 
    
          " 
     DESCRIPTION   
          "The SCSI MIB" 
           
   -- Revision History 
    
     REVISION     "200202250000Z"            
     DESCRIPTION  " Initial version published as RFC nnnn." 
 
     ::= { mib-2 999}   -- must be changed in the future 
    
       
   ---------------------- Textual Conventions ------------------------- 
   ScsiLUNOrZero  ::= TEXTUAL-CONVENTION 
     STATUS current 
     DESCRIPTION 
          " This Textual Convention represents either a SCSI Logical 
          Unit Number (LUN) or a zero-length string.  Objects defined 
          with this syntax must specify the meaning of the zero-length 
          string.  The format of a LUN is: 
          - a zero-length octet string or  
          - a string of two octets if the underlying transport protocol 
          is SBP-3 or SPI-4 using data group transfers or 
          - a string of eight octets for all other cases." 
     SYNTAX OCTET STRING (SIZE (0 | 2 | 8)) 
    
   ScsiIndexValue   ::= TEXTUAL-CONVENTION 
     STATUS current 
     DESCRIPTION 
          " An arbitrary integer value, greater than zero, for use as a 
          unique index value." 
     SYNTAX    Unsigned32(1..4294967295) 
      
   ScsiPortIndexValueOrZero ::= TEXTUAL-CONVENTION 
     STATUS current 
     DESCRIPTION 
          "This textual convention is an extension of the 
          ScsiIndexValue convention.  The latter defines a greater than 
          zero value used to identify an index.  This extension permits 
          the additional value of zero and is applicable only to 
          indices of SCSI port.  Usage of the zero is object-specific 
          and must therefore be defined as part of the description of 
          any object, which uses this syntax.  Examples of the usage of 
          zero might include situations where index was unknown, or 
          when none or all indices need to be referenced." 
     SYNTAX    Unsigned32(0..4294967295) 
    
   ScsiIndexValueOrZero ::= TEXTUAL-CONVENTION 
     STATUS current 
     DESCRIPTION 
          "This textual convention is an extension of the 
          ScsiIndexValue convention.  The latter defines a greater than 
          zero value used to identify an index.  This extension permits 
          the additional value of zero. Usage of the zero is object-
          specific and must therefore be defined as part of the 
          description of any object, which uses this syntax.  Examples 
          of the usage of zero might include situations where index was 
          unknown, or when none or all indices need to be referenced." 
     SYNTAX    Unsigned32(0..4294967295) 
    
   ScsiIdentifier ::= TEXTUAL-CONVENTION 
     STATUS    current 
 
     DESCRIPTION 
          "This Textual Convention represents a generic SCSI device or 
          port identifier. 
          The format depends on the transport used: 
          - SPI: only bits:0-3 for a port identifier (LSB is 0 and MSB 
          is 3). Other bits must be zero.  
          - SPI: identifier of a device is a zero-length octet string. 
          - FCP: 3 bytes for a port identifier 
          - FCP: identifier of a device is a zero-length octet string. 
          - SRP: 16 bytes for a port identifier. 
          - SRP: it is a zero-length octet string for a device 
          identifier. 
          - iSCSI: 256 bytes for a device identifier. 
          - iSCSI: 258 bytes for a target port identifier. 
          - iSCSI: 262 bytes for an initiator port identifier. 
          - SBP: it is a zero-length octet string for a device 
          identifier. 
          - SBP: 2 bytes for an initiator port identifier. 
          - SBP: 11 bytes for a target port identifier. " 
     SYNTAX OCTET STRING (SIZE (0 | 1 | 2 | 3| 11 | 16 | 256| 258|262)) 
    
   ScsiName ::= TEXTUAL-CONVENTION 
     STATUS    current 
     DESCRIPTION 
          " This Textual Convention represents a generic SCSI device or 
          port name. 
          The format depends on the transport used: 
          - SPI: it is a zero-length octet string for a device or port 
          name. 
          - FCP: 8 bytes for a port name. 
          - FCP: it is a zero-length octet string for a device name. 
          - SRP: 16 bytes for a port name. 
          - SRP: it is a zero-length octet string for a device name. 
          - iSCSI: 256 bytes for a device name. 
          - iSCSI: 258 bytes for a target port name. 
          - iSCSI: 262 bytes for an initiator port name. 
          - SBP: it is a zero-length octet string for a device name. 
          - SBP: 8 bytes for an initiator port name. 
          - SBP: 11 bytes for a target port name. " 
     SYNTAX OCTET STRING (SIZE (0 | 8 | 11 |16 | 256 | 258| 262)) 
    
   ScsiNameIdOrZero ::= TEXTUAL-CONVENTION 
     STATUS current 
     DESCRIPTION 
          " This Textual Convention represents either the SCSI name of 
          a logical unit or a zero-length string.  Objects defined with 
          this syntax must specify the meaning of the zero-length 
          string.  The format of the name of a LU is: 
          - a zero-length octet string or  
          - a string of eight octets." 
   SYNTAX OCTET STRING (SIZE (0 | 8)) 
    
   ScsiDeviceOrPort ::= TEXTUAL-CONVENTION 
 
     STATUS    current 
     DESCRIPTION 
          "This type specifies whether a particular configuration is 
          applicable to a port or to a device." 
     SYNTAX    INTEGER   { 
          device(1), 
          port(2), 
          other(3) 
     } 
    
   ScsiIdCodeSet ::= TEXTUAL-CONVENTION 
     STATUS    current 
     DESCRIPTION 
          "This Textual Convention specifies the code set in use with 
          this identifier. 
          The format is the same as contained in the identifier's 
          Identification Descriptor within the Logical Unit's Device 
          Identification Page." 
     REFERENCE  
          " ANSI - SCSI Primary Commands - 2 (SPC-2), Revision 20, 18 
          July 2001 Chapter 8: section 8.4.4, page 210 Vital Product 
          Data Parameters [16]" 
     SYNTAX    Unsigned32(0..15) 
    
   ScsiIdAssociation ::= TEXTUAL-CONVENTION 
     STATUS    current 
     DESCRIPTION 
          "This Textual Convention specifies what the identifier is 
          associated with (e.g, with the addressed physical/logical 
          device or with a particular port).   
          The format is the same as contained in the identifier's 
          Identification Descriptor within the Logical Unit's Device 
          Identification Page." 
     REFERENCE  
          " ANSI - SCSI Primary Commands - 2 (SPC-2), Revision 20, 18 
          July 2001 - Chapter 8: section 8.4.4, page 210 Vital Product 
          Data Parameters [16]" 
     SYNTAX    Unsigned32(0..3) 
    
   ScsiIdType ::= TEXTUAL-CONVENTION 
     STATUS    current 
     DESCRIPTION 
          "This Textual Convention specifies the type of the 
          identifier.  
          The format is the same as contained in the identifier's 
          Identification Descriptor within the Logical Unit's Device 
          Identification Page." 
     REFERENCE  
          " ANSI - SCSI Primary Commands - 2 (SPC-2), Revision 20, 
          Chapter 8: section 8.4.4, page 210 Vital Product Data 
          Parameters  [16]" 
     SYNTAX    Unsigned32(0..15) 
    
 
   ScsiIdValue ::= TEXTUAL-CONVENTION 
     STATUS    current 
     DESCRIPTION 
          "This Textual Convention represents an identifier. The 
          objects of type ScsiIdCodeSet, ScsIdAssociation, ScsiIdType, 
          define together the format. 
          The format is the same as contained in the identifier's 
          Identification Descriptor within the Logical Unit's Device 
          Identification Page." 
     REFERENCE  
          " ANSI - SCSI Primary Commands - 2 (SPC-2), Revision 20, 18 
          July 2001 - Chapter 8: section 8.4.4, page 210 Vital Product 
          Data Parameters [16]" 
     SYNTAX    OCTET STRING (SIZE (0..255)) 
    
    
   HrSWInstalledIndexOrZero ::= TEXTUAL-CONVENTION 
     STATUS current 
     DESCRIPTION 
          "The index value for a software module's row in the Host 
          Resources MIB's hrSWInstalledTable.  A zero value indicates 
          that no row in the hrSWInstalledTable is applicable." 
     REFERENCE 
          "hrSWInstalledTable is defined in the Host Resources MIB, RFC 
          2790." 
     SYNTAX   Integer32 (0..2147483647) 
    
   ----------------------- Structure of the MIB ---------------------- 
    
   scsiObjects           OBJECT IDENTIFIER ::= { scsiModule 1 } 
   scsiNotifications     OBJECT IDENTIFIER ::= { scsiModule 2 } 
   scsiConformance       OBJECT IDENTIFIER ::= { scsiModule 3 } 
    
   scsiTransportTypes    OBJECT IDENTIFIER ::= { scsiObjects 1 } 
   scsiGeneral           OBJECT IDENTIFIER ::= { scsiObjects 2 } 
   scsiInitiator         OBJECT IDENTIFIER ::= { scsiObjects 3 } 
   scsiTarget            OBJECT IDENTIFIER ::= { scsiObjects 4 } 
   scsiLogicalUnit       OBJECT IDENTIFIER ::= { scsiObjects 5 } 
    
    
   -- Transport Types 
   scsiTranportOther     OBJECT IDENTIFIER ::= { scsiTransportTypes 1 } 
   scsiTranportSPI       OBJECT IDENTIFIER ::= { scsiTransportTypes 2 } 
   scsiTransportFCP      OBJECT IDENTIFIER ::= { scsiTransportTypes 3 } 
   scsiTransportSRP      OBJECT IDENTIFIER ::= { scsiTransportTypes 4 } 
   scsiTransportISCSI    OBJECT IDENTIFIER ::= { scsiTransportTypes 5 } 
   scsiTransportSBP      OBJECT IDENTIFIER ::= { scsiTransportTypes 6 } 
    
    
   ----------------------- Instance Table ----------------------------- 
   scsiInstanceTable OBJECT-TYPE 
     SYNTAX         SEQUENCE OF ScsiInstanceEntry 
     MAX-ACCESS     not-accessible 
 
     STATUS         current 
     DESCRIPTION 
          "A list of SCSI instances present on the system. 
          The SCSI Instance is the top-level entity, to which 
          everything else belongs. An SNMP agent could represent more 
          than one instance if it represents either a stack of devices, 
          or virtual partitions of a larger device, or a host running 
          multiple SCSI implementations from different vendors." 
     ::= { scsiGeneral 1 } 
    
   scsiInstanceEntry OBJECT-TYPE 
     SYNTAX         ScsiInstanceEntry 
     MAX-ACCESS     not-accessible 
     STATUS         current 
     DESCRIPTION 
          "An entry (row) containing management information applicable 
          to a particular SCSI instance." 
     INDEX { scsiInstIndex } 
     ::= { scsiInstanceTable 1 } 
    
   ScsiInstanceEntry::= SEQUENCE { 
          scsiInstIndex                 ScsiIndexValue, 
          scsiInstAlias                 SnmpAdminString, 
          scsiInstSoftwareIndex         HrSWInstalledIndexOrZero, 
          scsiInstVendorVersion         SnmpAdminString, 
          scsiInstScsiNotificationsEnable    TruthValue 
   } 
    
   scsiInstIndex OBJECT-TYPE 
     SYNTAX         ScsiIndexValue 
     MAX-ACCESS     not-accessible 
     STATUS         current 
     DESCRIPTION 
          "This object represents an arbitrary integer used to uniquely 
          identify a particular SCSI instance." 
     ::= { scsiInstanceEntry 1 } 
    
   scsiInstAlias OBJECT-TYPE 
     SYNTAX         SnmpAdminString (SIZE(0..79)) 
     MAX-ACCESS     read-write 
     STATUS         current 
     DESCRIPTION 
          "This object represents an administrative string, configured 
          by the administrator. It can be a zero-length string." 
     ::= { scsiInstanceEntry 2 } 
    
   scsiInstSoftwareIndex    OBJECT-TYPE 
     SYNTAX         HrSWInstalledIndexOrZero 
     MAX-ACCESS     read-only 
     STATUS         current 
     DESCRIPTION 
          "If this management instance corresponds to an installed 
          software module, then this object's value is the value of the 
 
          hrSWInstalledIndex of that module.  If there is no 
          correspondence to an installed software module (or no module 
          which has a hrSWInstalledIndex value), then the value of this 
          object is zero." 
     REFERENCE 
          "hrSWInstalledIndex is defined in the Host Resources MIB, RFC 
          2790." 
     ::= { scsiInstanceEntry 3 } 
    
   scsiInstVendorVersion OBJECT-TYPE 
     SYNTAX         SnmpAdminString(SIZE(0..79)) 
     MAX-ACCESS     read-only 
     STATUS         current 
     DESCRIPTION 
          "This object represents a text string set by the manufacturer 
          describing the version of this instance.  The format of this 
          string is determined solely by the manufacturer, and is for 
          informational purposes only.  It is unrelated to the SCSI 
          specification version numbers." 
     ::= { scsiInstanceEntry 4 } 
    
   scsiInstScsiNotificationsEnable OBJECT-TYPE 
     SYNTAX         TruthValue 
     MAX-ACCESS     read-write 
     STATUS         current 
     DESCRIPTION 
          "This object allows to enable/disable sending all the 
          notifications defined in this MIB." 
     DEFVAL { true } 
     ::= { scsiInstanceEntry 5 } 
    
    
   scsiDeviceTable  OBJECT-TYPE 
     SYNTAX           SEQUENCE OF ScsiDeviceEntry 
     MAX-ACCESS       not-accessible 
     STATUS           current 
     DESCRIPTION 
          "A list of SCSI Devices present on the system." 
     ::= { scsiGeneral 2 } 
    
   scsiDeviceEntry OBJECT-TYPE 
     SYNTAX         ScsiDeviceEntry 
     MAX-ACCESS     not-accessible 
     STATUS         current 
     DESCRIPTION 
          "An entry (row) containing management information applicable 
          to a particular SCSI Device included in this SCSI manageable 
          instance." 
     INDEX { scsiInstIndex, scsiDeviceIndex } 
     ::= { scsiDeviceTable 1 } 
    
   ScsiDeviceEntry::= SEQUENCE { 
 
          scsiDeviceIndex          ScsiIndexValue, 
          scsiDeviceAlias          SnmpAdminString, 
          scsiDeviceRole           BITS, 
          scsiDevicePortNumber     Unsigned32, 
          scsiDeviceResets         Counter32 
   } 
    
   scsiDeviceIndex OBJECT-TYPE 
     SYNTAX         ScsiIndexValue 
     MAX-ACCESS     not-accessible 
     STATUS         current 
     DESCRIPTION 
          " This object is an arbitrary integer used to uniquely 
          identify a particular device within a particular SCSI 
          instance." 
     ::= { scsiDeviceEntry 1 } 
    
   scsiDeviceAlias OBJECT-TYPE 
     SYNTAX         SnmpAdminString (SIZE(0..79)) 
     MAX-ACCESS     read-write 
     STATUS         current 
     DESCRIPTION 
          " This object represents is an admistrative name for this 
          device. If no name is assigned, the value of this object is 
          the zero-length string." 
     ::= { scsiDeviceEntry 2 } 
    
   scsiDeviceRole OBJECT-TYPE 
     SYNTAX    BITS { 
               target(0), 
               initiator(1) 
          } 
     MAX-ACCESS     read-only 
     STATUS         current 
     DESCRIPTION 
          " This object determines whether this device is acting as an 
          initiator device, or as a target device or as both." 
     ::= { scsiDeviceEntry 3 } 
    
   scsiDevicePortNumber OBJECT-TYPE 
     SYNTAX         Unsigned32 
     MAX-ACCESS     read-only 
     STATUS         current 
     DESCRIPTION 
       "This object represents the number of ports contained in this 
       device." 
     ::= { scsiDeviceEntry 4 } 
    
   scsiDeviceResets      OBJECT-TYPE 
     SYNTAX         Counter32 
     MAX-ACCESS     read-only 
     STATUS         current 
     DESCRIPTION 
 
          "This object represents the number of times that this device 
          has reset." 
     ::= { scsiDeviceEntry 5 } 
    
    
   ----------------------- Port Table ---------------------------------
   scsiPortTable  OBJECT-TYPE 
     SYNTAX  SEQUENCE OF ScsiPortEntry 
     MAX-ACCESS       not-accessible 
     STATUS           current 
     DESCRIPTION 
          "A list of SCSI Ports for each SCSI device in each instance." 
     ::= { scsiGeneral 3 } 
    
   scsiPortEntry OBJECT-TYPE 
     SYNTAX              ScsiPortEntry 
     MAX-ACCESS          not-accessible 
     STATUS              current 
     DESCRIPTION 
          "An entry (row) containing management information applicable 
          to a particular SCSI port of a particular SCSI device in a 
          particular SCSI instance." 
     INDEX { scsiInstIndex, scsiDeviceIndex, scsiPortIndex } 
     ::= { scsiPortTable  1 } 
    
   ScsiPortEntry ::= SEQUENCE { 
     scsiPortIndex            ScsiIndexValue, 
     scsiPortRole             BITS, 
     scsiPortTrnsptPtr        OCTET STRING, -- was RowPointer, 
     scsiPortBusyStatuses     Counter32 
   } 
    
   scsiPortIndex OBJECT-TYPE 
     SYNTAX         ScsiIndexValue 
     MAX-ACCESS     not-accessible 
     STATUS         current 
     DESCRIPTION 
          "An arbitrary integer used to uniquely identify a particular 
          port of a given device within a particular SCSI instance." 
     ::= { scsiPortEntry 1 } 
    
   scsiPortRole OBJECT-TYPE 
     SYNTAX    BITS { 
               target(0), 
               initiator(1) 
          } 
     MAX-ACCESS     read-only 
     STATUS         current 
     DESCRIPTION 
          "This object indicates whether this port is acting as an 
          initiator port, or as a target port or as both." 
     ::= { scsiPortEntry 2 } 
    
 
   scsiPortTrnsptPtr OBJECT-TYPE 
     SYNTAX         OCTET STRING  (SIZE(1..255))  -- was RowPointer 
     MAX-ACCESS     read-only 
     STATUS         current 
     DESCRIPTION 
       "This object is a pointer to the corresponding row in the 
       scsiTrnsptTable" 
     ::= { scsiPortEntry 3 } 
    
   scsiPortBusyStatuses OBJECT-TYPE 
     SYNTAX         Counter32 
     MAX-ACCESS     read-only 
     STATUS         current 
     DESCRIPTION 
          "This object represents the number of port busy status sent 
          or received by this port. Note: Initiator ports only receive 
          busy status and target ports only send busy status." 
     ::= { scsiPortEntry 4 } 
    
   scsiTrnsptTable OBJECT-TYPE 
     SYNTAX           SEQUENCE OF ScsiTrnsptEntry 
     MAX-ACCESS       not-accessible 
     STATUS           current 
     DESCRIPTION 
          "This table contains a list of transports in use with each 
          SCSI device." 
     ::= { scsiGeneral 5 } 
    
   scsiTrnsptEntry OBJECT-TYPE 
     SYNTAX              ScsiTrnsptEntry 
     MAX-ACCESS          not-accessible 
     STATUS              current 
     DESCRIPTION 
          "An entry (row) containing parameters applicable to a 
          transport used by a particular device of a particular SCSI 
          manageable instance." 
     INDEX { scsiInstIndex, scsiDeviceIndex, scsiTrnsptIndex} 
     ::= { scsiTrnsptTable 1 } 
    
   ScsiTrnsptEntry ::= SEQUENCE { 
     scsiTrnsptIndex     ScsiIndexValue, 
     scsiTrnsptType      OCTET STRING, -- was AutonomousType, 
     scsiTrnsptPointer   OCTET STRING, -- was RowPointer, 
     scsiTrnsptDevName   ScsiName 
   } 
    
   scsiTrnsptIndex  OBJECT-TYPE 
     SYNTAX         ScsiIndexValue 
     MAX-ACCESS     not-accessible 
     STATUS         current 
     DESCRIPTION 
 
          "An arbitrary integer used to uniquely identify a particular 
          transport within a given device within a particular SCSI 
          instance." 
     ::= { scsiTrnsptEntry 1 } 
    
   scsiTrnsptType   OBJECT-TYPE 
     SYNTAX         OCTET STRING (SIZE (0..255))  -- was AutonomousType 
     MAX-ACCESS     read-only 
     STATUS         current 
     DESCRIPTION 
          " This object represents the type of transport for this 
          particular transport." 
     ::= { scsiTrnsptEntry 2 } 
    
   scsiTrnsptPointer     OBJECT-TYPE 
     SYNTAX         OCTET STRING  (SIZE(1..255))  -- was RowPointer 
     MAX-ACCESS     read-only 
     STATUS         current 
     DESCRIPTION 
          " This object represents a pointer to a conceptual row in a 
          'transport' MIB allowing a manager to get useful information 
          for the transport described by this entry. 
          For example, if the transport of this device is iSCSI, this 
          object will point to the iSCSI Instance of the iSCSI MIB. 
          If there is no MIB for this transport, this object has the 
          value 0.0." 
     ::= { scsiTrnsptEntry 3 } 
    
    
   scsiTrnsptDevName     OBJECT-TYPE 
     SYNTAX         ScsiName 
     MAX-ACCESS     read-only 
     STATUS         current 
     DESCRIPTION 
          " This object represents the name of this device in one of 
          the format(s) appropriate for this type of transport." 
     ::= { scsiTrnsptEntry 4 } 
    
    
   ----------------------- Initiator Device Table ---------------------
   scsiIntrDevTable  OBJECT-TYPE 
     SYNTAX           SEQUENCE OF ScsiIntrDevEntry 
     MAX-ACCESS       not-accessible 
     STATUS           current 
     DESCRIPTION 
          "This table contains information for each local initiator 
          device." 
    ::= { scsiInitiator 1} 
    
   scsiIntrDevEntry OBJECT-TYPE 
     SYNTAX           ScsiIntrDevEntry 
     MAX-ACCESS       not-accessible 
     STATUS           current 
 
     DESCRIPTION 
          "An entry (row) containing information applicable to an 
          initiator device within a particular SCSI instance." 
     INDEX { scsiInstIndex, scsiDeviceIndex } 
     ::= { scsiIntrDevTable  1 } 
    
   ScsiIntrDevEntry ::= SEQUENCE { 
     scsiIntrDevTgtAccessMode INTEGER, 
     scsiIntrDevOutResets     Counter32 
     } 
    
   scsiIntrDevTgtAccessMode   OBJECT-TYPE 
     SYNTAX    INTEGER { 
               unknown(1), 
               autoEnable(2), 
               manualEnable(3) 
     } 
     MAX-ACCESS     read-write 
     STATUS         current 
     DESCRIPTION 
          "This object controls whether a discovered target is 
          immediately authorized or not: 
          - autoEnable (2) means that when an initiator discovers a 
          target, it can use it immediately,  
          - manualEnable (3) means that the initiator must wait for an 
          operator to set scsiIntrDscTgtConfigured = true before it is 
          authorized." 
     ::= { scsiIntrDevEntry 1 } 
    
   scsiIntrDevOutResets  OBJECT-TYPE 
     SYNTAX         Counter32 
     MAX-ACCESS     read-only 
     STATUS         current 
     DESCRIPTION 
          " This object represents the number of resets sent by this 
          initiator."  
     ::= { scsiIntrDevEntry 2 } 
    
     
    
   -- The following section describes managed objects related to  
   -- initiator ports. 
   scsiIntrPrtTable OBJECT-TYPE 
     SYNTAX          SEQUENCE OF ScsiIntrPrtEntry 
     MAX-ACCESS      not-accessible 
     STATUS          current 
     DESCRIPTION 
          "This table contains all the initiator ports of local SCSI 
          Initiator or Target/Initiator devices." 
     ::= { scsiInitiator 3 } 
    
   scsiIntrPrtEntry OBJECT-TYPE 
     SYNTAX          ScsiIntrPrtEntry 
 
     MAX-ACCESS      not-accessible 
     STATUS          current 
     DESCRIPTION 
          "An entry (row) containing information applicable to a 
          particular initiator port of a particular device within a 
          SCSI instance. " 
   INDEX { scsiInstIndex, scsiDeviceIndex, scsiPortIndex } 
     ::= { scsiIntrPrtTable 1 } 
    
   ScsiIntrPrtEntry ::= SEQUENCE { 
     scsiIntrPrtName               ScsiName, 
     scsiIntrPrtIdentifier         ScsiIdentifier, 
     scsiIntrPrtOutCommands        Counter32, 
     scsiIntrPrtWrittenMegaBytes   Counter32, 
     scsiIntrPrtReadMegaBytes      Counter32, 
     scsiIntrPrtHSOutCommands      Counter64 
   } 
    
    
   scsiIntrPrtName OBJECT-TYPE 
     SYNTAX         ScsiName 
     MAX-ACCESS     read-only 
     STATUS         current 
     DESCRIPTION 
          " This object represents the name of the port assigned for 
          use by the SCSI protocol. The format will depend of the type 
          of transport this port is using." 
     ::= { scsiIntrPrtEntry 1 } 
    
    
   scsiIntrPrtIdentifier OBJECT-TYPE 
     SYNTAX         ScsiIdentifier 
     MAX-ACCESS     read-only 
     STATUS         current 
     DESCRIPTION 
          " This object represents the identifier of the port in one of 
          the format(s) appropriate for the type of transport in use." 
     ::= { scsiIntrPrtEntry 2 } 
    
   scsiIntrPrtOutCommands     OBJECT-TYPE 
     SYNTAX         Counter32 
     UNITS          "commands" 
     MAX-ACCESS     read-only 
     STATUS         current 
     DESCRIPTION 
          "This object represents the number of commands sent by this 
          initiator." 
     ::= { scsiIntrPrtEntry 3 } 
    
   scsiIntrPrtWrittenMegaBytes          OBJECT-TYPE 
     SYNTAX         Counter32 
     UNITS          "Megabytes" 
     MAX-ACCESS     read-only 
 
     STATUS         current 
     DESCRIPTION 
          "This object represents the amount of data in Megabytes sent 
          by this initiator." 
     ::= { scsiIntrPrtEntry 4 } 
    
 
   scsiIntrPrtReadMegaBytes   OBJECT-TYPE 
     SYNTAX         Counter32 
     UNITS          "Megabytes" 
     MAX-ACCESS     read-only 
     STATUS         current 
     DESCRIPTION 
          "This object represents the amount of data in Megabytes 
          received by this initiator." 
     ::= { scsiIntrPrtEntry 5 } 
    
   scsiIntrPrtHSOutCommands   OBJECT-TYPE 
     SYNTAX         Counter64 
     UNITS          "commands" 
     MAX-ACCESS     read-only 
     STATUS         current 
     DESCRIPTION 
          "This object represents the number of commands sent by this 
          initiator device. This object provides support for systems 
          which can quickly generate lots of commands because they run 
          at high speed." 
     ::= { scsiIntrPrtEntry 6 } 
    
   scsiRemoteTarget OBJECT IDENTIFIER ::= { scsiInitiator 4 } 
    
   -- Targets discovered or authorized to attach each of the initiator 
   -- ports of each initiator device of each instance.  
   scsiDscTgtTable OBJECT-TYPE 
     SYNTAX         SEQUENCE OF ScsiDscTgtEntry 
     MAX-ACCESS      not-accessible 
     STATUS          current 
     DESCRIPTION 
          "This table includes all the remote (not in the local system) 
          target ports that are authorized to attach to each local 
          initiator port of this SCSI instance." 
     ::= { scsiRemoteTarget 1 } 
    
   scsiDscTgtEntry OBJECT-TYPE 
     SYNTAX              ScsiDscTgtEntry 
     MAX-ACCESS          not-accessible 
     STATUS              current 
     DESCRIPTION 
          "An entry (row) represents an authorization for one or all 
          local initiator ports of a local device (scsiDeviceIndex) 
          within a local SCSI instance (scsiInstIndex), to attach to a 
          remote target port or device (scsiDscTgtIndex).  The 
 
          authorization is either for all local ports if 
          scsiDscTgtIntrPortIndex is zero, or otherwise only for the 
          specific port identified by scsiDscTgtIntrPortIndex. 
          Note that when an entry in this table is deleted, then any 
          corresponding entries in the scsiDscLunsTable should be 
          deleted as well." 
     INDEX { scsiInstIndex, scsiDeviceIndex, scsiDscTgtIntrPortIndex, 
     scsiDscTgtIndex } 
   ::= { scsiDscTgtTable 1 } 
    
   ScsiDscTgtEntry ::= SEQUENCE { 
     scsiDscTgtIntrPortIndex  ScsiPortIndexValueOrZero, 
     scsiDscTgtIndex          ScsiIndexValue, 
     scsiDscTgtDevOrPort      ScsiDeviceOrPort, 
     scsiDscTgtName           ScsiName, 
     scsiDscTgtConfigured     TruthValue, 
     scsiDscTgtDiscovered     TruthValue, 
     scsiDscTgtInCommands     Counter32, 
     scsiDscTgtWrittenMegaBytes    Counter32, 
     scsiDscTgtReadMegaBytes  Counter32, 
     scsiDscTgtHSInCommands   Counter64, 
     scsiDscTgtLastCreation   TimeStamp, 
     scsiDscTgtRowStatus      RowStatus 
   } 
    
    
   scsiDscTgtIntrPortIndex    OBJECT-TYPE 
     SYNTAX         ScsiPortIndexValueOrZero 
     MAX-ACCESS     not-accessible 
     STATUS         current 
     DESCRIPTION 
          "This object relates to a particular local device within a 
          particular SCSI instance and specifies: 
          - the index of the local scsi initiator port, 
          - or zero, if this entry refers to the local device and 
          therefore refers to all the local initiator ports." 
     ::= { scsiDscTgtEntry 1 } 
    
   scsiDscTgtIndex OBJECT-TYPE 
     SYNTAX         ScsiIndexValue 
     MAX-ACCESS     not-accessible 
     STATUS         current 
     DESCRIPTION 
          "This object is an arbitrary integer used to uniquely 
          identify a particular authorized target amongst those 
          authorized for one or more ports (of a particular device 
          within a particular SCSI instance) to attach to."  
     ::= { scsiDscTgtEntry 2 } 
    
   scsiDscTgtDevOrPort OBJECT-TYPE 
     SYNTAX         ScsiDeviceOrPort 
     MAX-ACCESS     read-create 
     STATUS         current 
 
     DESCRIPTION 
          "This object specifies whether the authorization represented 
          by this row applies to a remote target port or remote target 
          device." 
     ::= { scsiDscTgtEntry 3 } 
    
   scsiDscTgtName OBJECT-TYPE 
     SYNTAX         ScsiName 
     MAX-ACCESS     read-create 
     STATUS         current 
     DESCRIPTION 
          " This object represents the name of this 
          authorized/discovered target device or port." 
     ::= { scsiDscTgtEntry 4 } 
    
   scsiDscTgtConfigured OBJECT-TYPE 
     SYNTAX         TruthValue 
     MAX-ACCESS     read-create 
     STATUS         current 
     DESCRIPTION 
          "This object means: 
          -true(1): this entry has been configured by an administrator 
          -false(2): this entry has been added from other source. 
          An administrator can modify this value from false to true." 
     DEFVAL { true } 
     ::= { scsiDscTgtEntry 5 } 
    
   scsiDscTgtDiscovered OBJECT-TYPE 
     SYNTAX         TruthValue 
     MAX-ACCESS     read-only 
     STATUS         current 
     DESCRIPTION 
          "This object means: 
          -true(1): this entry has been discovered by the SCSI instance. 
          -false(2): this entry has been added from other source. 
          This entry is read-only because an administrator cannot 
          change it. 
          Note that it is an implementation decision to determine how 
          long to retain a row with configured=false, as and when the 
          target is no longer visible/accessible to the local 
          initiator." 
     ::= { scsiDscTgtEntry 6 } 
    
    
    
   scsiDscTgtInCommands  OBJECT-TYPE 
     SYNTAX         Counter32 
     UNITS          "commands" 
     MAX-ACCESS     read-only 
     STATUS         current 
     DESCRIPTION 
          "This object represents the number of commands received by 
          this target port or device." 
 
     ::= { scsiDscTgtEntry 7 } 
    
   scsiDscTgtWrittenMegaBytes OBJECT-TYPE 
     SYNTAX         Counter32 
     UNITS          "Megabytes" 
     MAX-ACCESS     read-only 
     STATUS         current 
     DESCRIPTION 
          "This object represents the amount of data in Megabytes 
          written by this target port or device." 
     ::= { scsiDscTgtEntry 8 } 
    
   scsiDscTgtReadMegaBytes    OBJECT-TYPE 
     SYNTAX         Counter32 
     UNITS          "Megabytes" 
     MAX-ACCESS     read-only 
     STATUS         current 
     DESCRIPTION 
          "This object represents the amount of data in Megabytes read 
          by this target port or device." 
     ::= { scsiDscTgtEntry 9 } 
    
   scsiDscTgtHSInCommands OBJECT-TYPE 
     SYNTAX         Counter64 
     UNITS          "commands" 
     MAX-ACCESS     read-only 
     STATUS         current 
     DESCRIPTION 
          "This object represents the number of commands received by 
          this target port or device. This object provides support for 
          systems which can quickly generate lots of commands because 
          they run at high speed." 
     ::= { scsiDscTgtEntry 10 } 
    
   scsiDscTgtLastCreation OBJECT-TYPE 
     SYNTAX         TimeStamp 
     MAX-ACCESS     read-only 
     STATUS         current 
     DESCRIPTION 
          "This object represents the value of sysUpTime when this row 
          was created." 
     ::= { scsiDscTgtEntry 11 } 
      
    
   scsiDscTgtRowStatus OBJECT-TYPE 
     SYNTAX         RowStatus 
     MAX-ACCESS     read-create 
     STATUS         current 
     DESCRIPTION 
          "This object allows to configure dynamically a new entry in 
          this table via SNMP or eventually delete it. 
 
          An administrator is not allowed to delete an entry for which 
          the value of the object scsiIntrDscTgtDiscovered is equal to 
          true.  
          Note that when an entry in this table is deleted, then any 
          corresponding entries in the scsiDscLunsTable must also be 
          automatically deleted. " 
     ::= { scsiDscTgtEntry 12 } 
    
   scsiDscLunTable OBJECT-TYPE 
     SYNTAX           SEQUENCE OF ScsiDscLunEntry 
     MAX-ACCESS       not-accessible 
     STATUS           current 
     DESCRIPTION 
          "This table includes all the remote (not in the local system) 
          logical unit numbers (LUNS) discovered via each local 
          initiator port of each local device within a particular SCSI 
          instance." 
     ::= { scsiRemoteTarget 2 } 
    
   scsiDscLunEntry OBJECT-TYPE 
     SYNTAX           ScsiDscLunEntry 
     MAX-ACCESS       not-accessible 
     STATUS           current 
     DESCRIPTION 
          "An entry (row) represents a discovered LUN at a particular 
          SCSI target device (scsiDscTgtIndex), where the LUN was 
          discovered by a particular local initiator device within a 
          particular SCSI instance, possibly via a particular local 
          initiator port. 
          Note that when an entry in the scsiDscTgtTable is deleted, 
          then any corresponding entries in this table is automatically 
          deleted." 
     INDEX { scsiInstIndex, scsiDeviceIndex, scsiDscTgtIntrPortIndex,   
     scsiDscTgtIndex, scsiDscLunIndex } 
     ::= { scsiDscLunTable 1 } 
    
   ScsiDscLunEntry ::= SEQUENCE { 
     scsiDscLunIndex     ScsiIndexValue, 
     scsiDscLunLun       ScsiLUNOrZero   
   } 
    
    
   scsiDscLunIndex OBJECT-TYPE 
     SYNTAX         ScsiIndexValue 
     MAX-ACCESS     not-accessible 
     STATUS         current 
     DESCRIPTION 
          "This object is an arbitrary integer used to uniquely 
          identify a particular LUN discovered by a particular scsi 
          initiator port or a particular SCSI initiator device within a 
          particular SCSI instance. Entries in the scsiDscLunIdTable 
 
          are associated with a LUN by having the value of this object 
          in their INDEX." 
     ::= { scsiDscLunEntry 1 } 
    
   scsiDscLunLun    OBJECT-TYPE 
     SYNTAX         ScsiLUNOrZero 
     MAX-ACCESS     read-only 
     STATUS         current 
     DESCRIPTION 
          "This object contains the Logical Unit Number (LUN) of the 
          discovered logical unit. 
          A value of zero has no meaning in this case." 
     ::= { scsiDscLunEntry 2 } 
    
    
   ----------------------- LU Identifiers discovered ------------------ 
   scsiDscLunIdTable OBJECT-TYPE 
     SYNTAX           SEQUENCE OF ScsiDscLunIdEntry 
     MAX-ACCESS       not-accessible 
     STATUS           current 
     DESCRIPTION 
          "This table includes all the known LU Identifiers of the 
          remote (not in the local system) logical units discovered via 
          each local initiator port or device of this SCSI instance." 
     ::= { scsiRemoteTarget 3 } 
    
   scsiDscLunIdEntry OBJECT-TYPE 
     SYNTAX           ScsiDscLunIdEntry 
     MAX-ACCESS       not-accessible 
     STATUS           current 
     DESCRIPTION 
          "An entry (row) represents the LU Identifier of a discovered 
          LUN at a particular SCSI target device (scsiDscTgtIndex), 
          where the LUN was discovered by a particular local initiator 
          device within a particular SCSI instance, possibly via a 
          particular local initiator port." 
     INDEX { scsiInstIndex, scsiDeviceIndex, scsiDscTgtIntrPortIndex, 
     scsiDscTgtIndex, scsiDscLunIndex, scsiDscLunIdIndex } 
     ::= { scsiDscLunIdTable 1 } 
    
   ScsiDscLunIdEntry ::= SEQUENCE { 
     scsiDscLunIdIndex        ScsiIndexValue, 
     scsiDscLunIdCodeSet      ScsiIdCodeSet, 
     scsiDscLunIdAssociation  ScsiIdAssociation, 
     scsiDscLunIdType         ScsiIdType, 
     scsiDscLunIdValue        ScsiIdValue 
   } 
    
    
   scsiDscLunIdIndex     OBJECT-TYPE 
     SYNTAX         ScsiIndexValue 
     MAX-ACCESS     not-accessible 
     STATUS         current 
 
     DESCRIPTION 
          "This object is an arbitrary integer used to uniquely 
          identify a particular LUN Identifier discovered by each scsi 
          initiator device or particular SCSI initiator port within a 
          particular SCSI instance." 
     ::= { scsiDscLunIdEntry 1 } 
    
   scsiDscLunIdCodeSet OBJECT-TYPE 
     SYNTAX          ScsiIdCodeSet 
     MAX-ACCESS      read-only 
     STATUS          current 
     DESCRIPTION 
          "This object specifies the code set in use with this 
          identifier. 
          The value is represented in the same format as is contained 
          in the identifier's Identification Descriptor within the 
          Logical Unit's Device Identification Page." 
     REFERENCE  
          " ANSI - SCSI Primary Commands - 2 (SPC-2),Revision 20,   
          Chapter 8: section 8.4.4, page 210 Vital Product Data 
          Parameters [16]" 
     ::= { scsiDscLunIdEntry 2 } 
    
   scsiDscLunIdAssociation OBJECT-TYPE 
     SYNTAX          ScsiIdAssociation  
     MAX-ACCESS      read-only 
     STATUS          current 
     DESCRIPTION 
          "This object specifies what the identifier is associated with 
          (e.g, with the addressed physical/logical device or with a 
          particular port).  The value is represented in the same 
          format as is contained in the identifier's Identification 
          Descriptor within the Logical Unit's Device Identification 
          Page." 
     REFERENCE  
          " ANSI - SCSI Primary Commands - 2 (SPC-2), Revision 20, 
          Chapter 8: section 8.4.4, page 210 Vital Product Data 
          Parameters [16]" 
     ::= { scsiDscLunIdEntry 3 } 
    
   scsiDscLunIdType OBJECT-TYPE 
     SYNTAX          ScsiIdType 
     MAX-ACCESS      read-only 
     STATUS          current 
     DESCRIPTION 
          "This object specifies the type of the identifier.  
          The value is represented in the same format as is contained 
          in the identifier's Identification Descriptor within the 
          Logical Unit's Device Identification Page." 
     REFERENCE  
          " ANSI - SCSI Primary Commands - 2 (SPC-2), Revision 20, 
          Chapter 8: section 8.4.4, page 210 Vital Product Data 
          Parameters  [16]" 
 
     ::= { scsiDscLunIdEntry 4 } 
    
   scsiDscLunIdValue OBJECT-TYPE 
     SYNTAX         ScsiIdValue  
     MAX-ACCESS     read-only 
     STATUS         current 
     DESCRIPTION 
          " This object represents the actual value of this identifier. 
          The format is defined by the objects scsiDscLunIdCodeSet, 
          scsiDscLunIdAssociation, scsiDscLunIdType. 
          The value is represented in the same format as is contained 
          in the identifier's Identification Descriptor within the 
          Logical Unit's Device Identification Page." 
     REFERENCE  
          " ANSI - SCSI Primary Commands - 2 (SPC-2), 
          Chapter 8: section 8.4.4, page 210 Vital Product Data 
     Parameters  [16]" 
     ::= { scsiDscLunIdEntry 5 } 
    
    
   scsiAttTgtPortTable OBJECT-TYPE 
     SYNTAX    SEQUENCE OF ScsiAttTgtPortEntry 
     MAX-ACCESS     not-accessible 
     STATUS         current 
     DESCRIPTION 
          "This table includes all the remote (not in the local system) 
          target ports that are currently attached to each local 
          initiator port of this SCSI instance." 
     ::= { scsiRemoteTarget 6 } 
    
   scsiAttTgtPortEntry OBJECT-TYPE 
     SYNTAX           ScsiAttTgtPortEntry 
     MAX-ACCESS       not-accessible 
     STATUS           current 
     DESCRIPTION 
       "An entry (row) represents a remote target port 
       (scsiAttTgtPortIndex) currently attached to a particular 
       initiator port (scsiPortIndex) of a particular SCSI initiator 
       device within a particular SCSI instance." 
     INDEX { scsiInstIndex, scsiDeviceIndex, scsiPortIndex, 
     scsiAttTgtPortIndex } 
   ::= { scsiAttTgtPortTable 1 } 
    
   ScsiAttTgtPortEntry ::= SEQUENCE { 
     scsiAttTgtPortIndex      ScsiIndexValue, 
     scsiAttTgtPortDscTgtIdx  ScsiIndexValueOrZero, 
     scsiAttTgtPortName       ScsiName, 
     scsiAttTgtPortIdentifier ScsiIdentifier 
   } 
    
   scsiAttTgtPortIndex   OBJECT-TYPE 
 
     SYNTAX         ScsiIndexValue 
     MAX-ACCESS     not-accessible 
     STATUS         current 
     DESCRIPTION 
          "An arbitrary integer used to uniquely identify a particular 
          target currently attached to a particular SCSI initiator port 
          of a particular SCSI initiator device within a particular 
          SCSI instance." 
     ::= { scsiAttTgtPortEntry 1 } 
    
   scsiAttTgtPortDscTgtIdx    OBJECT-TYPE 
     SYNTAX         ScsiIndexValueOrZero 
     MAX-ACCESS     read-only 
     STATUS         current 
     DESCRIPTION 
          "This object contains the value of the scsiAttTgtPortIndex 
          index variable for the row in the scsiDscTgtTable 
          representing this currently attached target port.  If the 
          currently attached target port is not represented in the 
          scsiDscTgtTable, then the value of this object is zero." 
     ::= { scsiAttTgtPortEntry 2 } 
    
   scsiAttTgtPortName OBJECT-TYPE 
     SYNTAX         ScsiName 
     MAX-ACCESS     read-only 
     STATUS         current 
     DESCRIPTION 
          " This object contains the name of the attached target port." 
     ::= { scsiAttTgtPortEntry 3 } 
    
    
   scsiAttTgtPortIdentifier OBJECT-TYPE 
     SYNTAX         ScsiIdentifier 
     MAX-ACCESS     read-only 
     STATUS         current 
     DESCRIPTION 
          " This object contains the identifier of the attached target 
          port." 
     ::= { scsiAttTgtPortEntry 4 } 
    
    
    
   -- Management Objects regarding target type of scsi devices 
   --  
   scsiTgtDevTable OBJECT-TYPE 
     SYNTAX  SEQUENCE OF ScsiTgtDevEntry 
     MAX-ACCESS      not-accessible 
     STATUS          current 
     DESCRIPTION 
          "This table contains information about each local target 
          device."  
     ::= { scsiTarget 1 } 
    
 
   scsiTgtDevEntry OBJECT-TYPE 
     SYNTAX           ScsiTgtDevEntry 
     MAX-ACCESS       not-accessible 
     STATUS           current 
     DESCRIPTION 
          "An entry (row) containing information applicable to a 
          particular local target device within a particular SCSI 
          instance. " 
     INDEX { scsiInstIndex, scsiDeviceIndex } 
     ::= { scsiTgtDevTable 1 } 
    
   ScsiTgtDevEntry ::= SEQUENCE { 
     scsiTgtDevNumberOfLUs         Gauge32, 
     scsiTgtDeviceStatus           INTEGER, 
     scsiTgtDevNonAccessibleLUs    Gauge32 
   } 
    
   scsiTgtDevNumberOfLUs OBJECT-TYPE 
     SYNTAX         Gauge32 
     MAX-ACCESS     read-only 
     STATUS         current 
     DESCRIPTION 
          "This object is the number of Logical Units accessible via 
          this local target device." 
     ::= { scsiTgtDevEntry 1 } 
    
   scsiTgtDeviceStatus   OBJECT-TYPE 
     SYNTAX         INTEGER { 
          unknown(1), 
          available(2), 
          broken(3), 
          readying(4), 
          abnormal(5), 
          nonAddrFailure(6), 
          nonAddrFailReadying(7), 
          nonAddrFailAbnormal(8) 
     } 
     MAX-ACCESS     read-only 
     STATUS         current 
     DESCRIPTION 
          " This object represents the status of this SCSI device, 
          summarizing the state of both the addressable devices (i.e., 
          the logical units) and the non-addressable devices within 
          this SCSI device: 
          - unknown(1): This value is used when the status cannot be 
          determined 
          - available(2): All addressable and non-addressable devices 
          within the SCSI device are fully operational (i.e., no 
          logical units have an abnormal status). 
          - broken(3): The SCSI device is not operational and cannot be 
          made operational without external intervention. 
          - readying(4): One or more logical units within the SCSI 
          device are being initialized and access to the SCSI device is 
 
          temporarily limited (i.e., one or more of the logical unit 
          have a readying status). 
          - abnormal(5): One or more addressable devices within the 
          SCSI device are indicating a status other than available; 
          nevertheless, the SCSI device is operational (i.e., one or 
          more of the logical units have an abnormal status). 
          - nonAddrFailure(6): One or more non-addressable devices 
          within the SCSI device have failed; nevertheless, the SCSI 
          device is operational (i.e., no logical units have an 
          abnormal or readying status). 
          - nonAddrFailReadying(7): One or more non-addressable devices 
          within the SCSI device have failed; nevertheless,one or more 
          logical units within the SCSI device are being initialized 
          and access to the SCSI device is temporarily limited. 
          - nonAddrFailAbnormal(8): One or more non-addressable devices 
          within the SCSI device have failed and one or more 
          addressable devices within the SCSI device are indicating a 
          status other than available however the SCSI device is 
          operational. 
          " 
     REFERENCE  
          "SCSI Controller Commands-2 (SCC-2) standard NCITS.318-1998 
          6.3.1.8 REPORT STATES service action" 
     ::= { scsiTgtDevEntry 2} 
    
    
   scsiTgtDevNonAccessibleLUs OBJECT-TYPE 
     SYNTAX         Gauge32 
     MAX-ACCESS     read-only 
     STATUS         current 
     DESCRIPTION 
          "This object is the number of Logical Units existing but not 
          currently accessible via this local target device." 
     ::= { scsiTgtDevEntry 3 } 
    
   -- Target Port Table 
   scsiTgtPortTable OBJECT-TYPE 
     SYNTAX    SEQUENCE OF ScsiTgtPortEntry 
     MAX-ACCESS     not-accessible 
     STATUS         current 
     DESCRIPTION 
          "This table includes all the local target ports of all the 
          local target devices." 
     ::= { scsiTarget 2 } 
    
   scsiTgtPortEntry OBJECT-TYPE 
     SYNTAX           ScsiTgtPortEntry 
     MAX-ACCESS       not-accessible 
     STATUS           current 
     DESCRIPTION 
          "An entry (row) containing information applicable to a 
          particular local target port of a particular local target 
          device within a particular SCSI instance. " 
 
     INDEX { scsiInstIndex, scsiDeviceIndex, scsiPortIndex} 
     ::= { scsiTgtPortTable 1 } 
    
   ScsiTgtPortEntry ::= SEQUENCE { 
     scsiTgtPortName          ScsiName, 
     scsiTgtPortIdentifier    ScsiIdentifier, 
     scsiTgtPortInCommands    Counter32, 
     scsiTgtPortWrittenMegaBytes   Counter32, 
     scsiTgtPortReadMegaBytes Counter32, 
     scsiTgtPortHSInCommands  Counter64 
       } 
    
   scsiTgtPortName OBJECT-TYPE 
     SYNTAX         ScsiName 
     MAX-ACCESS     read-only 
     STATUS         current 
     DESCRIPTION 
          " This object represents the name of the port assigned for 
          use in the SCSI protocol." 
     ::= { scsiTgtPortEntry 1 } 
    
   scsiTgtPortIdentifier OBJECT-TYPE 
     SYNTAX         ScsiIdentifier 
     MAX-ACCESS     read-only 
     STATUS         current 
     DESCRIPTION 
          " This object represents the identifier of the port in one of 
          the format(s) appropriate for the type of transport." 
     ::= { scsiTgtPortEntry 2 } 
    
   scsiTgtPortInCommands OBJECT-TYPE 
     SYNTAX         Counter32 
     UNITS          "commands" 
     MAX-ACCESS     read-only 
     STATUS         current 
     DESCRIPTION 
          " This object represents the number of commands received by 
          this target port." 
     ::= { scsiTgtPortEntry 3 } 
      
           
   scsiTgtPortWrittenMegaBytes OBJECT-TYPE 
     SYNTAX         Counter32 
     UNITS          "Megabytes" 
     MAX-ACCESS     read-only 
     STATUS         current 
     DESCRIPTION 
          " This object represents the amount of data written in 
          Megabytes by this target port." 
     ::= { scsiTgtPortEntry 4 } 
    
   scsiTgtPortReadMegaBytes OBJECT-TYPE 
     SYNTAX         Counter32 
 
     UNITS          "Megabytes" 
     MAX-ACCESS     read-only 
     STATUS         current 
     DESCRIPTION 
          " This object represents the amount of data read in Megabytes 
          by this target port." 
     ::= { scsiTgtPortEntry 5 } 
    
   scsiTgtPortHSInCommands OBJECT-TYPE 
     SYNTAX         Counter64 
     UNITS          "commands" 
     MAX-ACCESS     read-only 
     STATUS         current 
     DESCRIPTION 
          " This object represents the number of commands received. 
          This object provides support for systems that can quickly 
          generate lots of commands because they run at high speed." 
     ::= { scsiTgtPortEntry 6 } 
    
    
   scsiRemoteInitiators OBJECT IDENTIFIER ::= { scsiTarget 3 } 
    
   -- The scsiAuthorizedIntrTable contains the list of remote initiator 
   -- ports that are authorized to be attached specific target ports  
   -- and on which, an administrator would like to keep permanent  
   -- information and long term statistics even when not currently  
   -- attached. 
    
   scsiAuthorizedIntrTable OBJECT-TYPE 
     SYNTAX    SEQUENCE OF ScsiAuthorizedIntrEntry 
     MAX-ACCESS  not-accessible 
     STATUS      current 
     DESCRIPTION 
          "This table includes all the authorized initiator devices or 
          ports that may attach a target device or port of the local 
          SCSI instance. Statistics are kept for each such 
          authorization; thus, the authorizations should be configured 
          in the manner, which will cause the desired set of statistics 
          to be collected and that will determine the correct LUN map." 
     ::= { scsiRemoteInitiators 1 } 
    
   scsiAuthorizedIntrEntry OBJECT-TYPE 
     SYNTAX         ScsiAuthorizedIntrEntry 
     MAX-ACCESS     not-accessible 
     STATUS         current 
     DESCRIPTION 
          "An entry (row) represents a remote initiator port or remote 
          initiator device that may attach to the local target port or 
          device within a particular SCSI instance." 
     INDEX { scsiInstIndex, scsiDeviceIndex, scsiAuthIntrTgtPortIndex, 
     scsiAuthIntrIndex } 
     ::= { scsiAuthorizedIntrTable 1 } 
    
 
   ScsiAuthorizedIntrEntry ::= SEQUENCE { 
     scsiAuthIntrTgtPortIndex      ScsiPortIndexValueOrZero, 
     scsiAuthIntrIndex             ScsiIndexValue, 
     scsiAuthIntrDevOrPort         ScsiDeviceOrPort, 
     scsiAuthIntrName              ScsiName, 
     scsiAuthIntrLunMapIndex       ScsiIndexValueOrZero, 
     scsiAuthIntrAttachedTimes     Counter32, 
     scsiAuthIntrOutCommands       Counter32, 
     scsiAuthIntrReadMegaBytes     Counter32, 
     scsiAuthIntrWrittenMegaBytes  Counter32, 
     scsiAuthIntrHSOutCommands     Counter64, 
     scsiAuthIntrLastCreation      TimeStamp, 
     scsiAuthIntrRowStatus         RowStatus 
     } 
    
    
   scsiAuthIntrTgtPortIndex   OBJECT-TYPE 
     SYNTAX         ScsiPortIndexValueOrZero 
     MAX-ACCESS     not-accessible 
     STATUS         current 
     DESCRIPTION 
          "This object contains either the index of the port, or zero 
          to indicate any port, on the particular local target device." 
     ::= { scsiAuthorizedIntrEntry 1 } 
    
   scsiAuthIntrIndex     OBJECT-TYPE 
     SYNTAX         ScsiIndexValue 
     MAX-ACCESS     not-accessible 
     STATUS         current 
     DESCRIPTION 
          "This object is an arbitrary integer used to uniquely 
          identify a SCSI initiator which is authorized to attach to a 
          particular local target device or port of a particular SCSI 
          instance." 
     ::= { scsiAuthorizedIntrEntry 2 } 
    
   scsiAuthIntrDevOrPort OBJECT-TYPE 
     SYNTAX         ScsiDeviceOrPort 
     MAX-ACCESS     read-create 
     STATUS         current 
     DESCRIPTION 
          "This object specifies if this entry refers to a remote 
          initiator port or a device. 
          A value of device(1) means that the authorized remote 
          initiator is a device and includes all its ports. 
          A value of port(2) means that the authorized remote initiator 
          is a port." 
     ::= { scsiAuthorizedIntrEntry 3 } 
    
   scsiAuthIntrName OBJECT-TYPE 
     SYNTAX         ScsiName 
     MAX-ACCESS     read-create 
     STATUS         current 
 
     DESCRIPTION 
          "This object represents the name of the remote initiator 
          device or port authorized by this row." 
     ::= { scsiAuthorizedIntrEntry 4 } 
    
   scsiAuthIntrLunMapIndex OBJECT-TYPE 
     SYNTAX         ScsiIndexValueOrZero 
     MAX-ACCESS     read-create 
     STATUS         current 
     DESCRIPTION 
          "This object identifies the set of entries in the 
          scsiLunMapTable for which scsiLunMapIndex has the same value 
          as the value of this object.  The identified set of entries 
          constitute the LUN map to be used for accessing logical units 
          when the remote initiator port or device corresponding to 
          this entry is attached to any local target port or device 
          corresponding to this entry. 
          Note that this object has a value of zero if this entry 
          should use the default LUN map." 
     ::= { scsiAuthorizedIntrEntry 5 } 
    
    
   scsiAuthIntrAttachedTimes  OBJECT-TYPE 
     SYNTAX         Counter32 
     UNITS          "Times" 
     MAX-ACCESS     read-only 
     STATUS         current 
     DESCRIPTION 
          "This object indicates the number of times that this remote 
          initiator has transitioned from unattached to attached to 
          this local target device or port." 
     ::= { scsiAuthorizedIntrEntry 6 }   
      
   scsiAuthIntrOutCommands    OBJECT-TYPE 
     SYNTAX         Counter32 
     UNITS          "commands" 
     MAX-ACCESS     read-only 
     STATUS         current 
     DESCRIPTION 
          "This object indicates the number of commands that the remote 
          initiator corresponding to this entry has sent to the local 
          target device or port corresponding to this entry." 
     ::= { scsiAuthorizedIntrEntry 7 } 
 
   scsiAuthIntrReadMegaBytes  OBJECT-TYPE 
     SYNTAX         Counter32 
     UNITS          "Megabytes" 
     MAX-ACCESS     read-only 
     STATUS         current 
     DESCRIPTION 
          "This object indicates the amount of data in Megabytes that 
          the remote initiator corresponding to this entry has read 
 
          from the local target device or port corresponding to this 
          entry." 
     ::= { scsiAuthorizedIntrEntry 8 } 
    
   scsiAuthIntrWrittenMegaBytes    OBJECT-TYPE 
     SYNTAX         Counter32 
     UNITS          "Megabytes" 
     MAX-ACCESS     read-only 
     STATUS         current 
     DESCRIPTION 
          "This object indicates the amount of data in Megabytes that 
          the remote initiator corresponding to this entry has written 
          from the local target device or port corresponding to this 
          entry." 
     ::= { scsiAuthorizedIntrEntry 9} 
    
    
   scsiAuthIntrHSOutCommands  OBJECT-TYPE 
     SYNTAX         Counter64 
     UNITS          "commands" 
     MAX-ACCESS     read-only 
     STATUS         current 
     DESCRIPTION 
          "This object represents the number of commands sent by the 
          remote initiator corresponding to this entry to the local 
          target device or port corresponding to this entry. This 
          object provides support for systems which can quickly 
          generate lots of commands because they run at high speed." 
     ::= { scsiAuthorizedIntrEntry 10 } 
    
   scsiAuthIntrLastCreation   OBJECT-TYPE 
     SYNTAX         TimeStamp 
     MAX-ACCESS     read-only 
     STATUS         current 
     DESCRIPTION 
          "This object indicates the value of sysUpTime when this row 
          was last created." 
     ::= { scsiAuthorizedIntrEntry 11 } 
             
   scsiAuthIntrRowStatus OBJECT-TYPE 
     SYNTAX         RowStatus 
     MAX-ACCESS     read-create 
     STATUS         current 
     DESCRIPTION 
          "This object allows an administrator to create or delete this 
          entry." 
     ::= { scsiAuthorizedIntrEntry 12 } 
    
   scsiAttIntrPrtTable OBJECT-TYPE 
     SYNTAX  SEQUENCE OF ScsiAttIntrPrtEntry 
     MAX-ACCESS      not-accessible 
     STATUS          current 
 
     DESCRIPTION 
          "This table includes all the remote initiator ports that are 
          currently attached to a local target port of all local 
          devices within all SCSI instances." 
     ::= { scsiRemoteInitiators 2 } 
    
   scsiAttIntrPrtEntry OBJECT-TYPE 
     SYNTAX          ScsiAttIntrPrtEntry 
     MAX-ACCESS      not-accessible 
     STATUS          current 
     DESCRIPTION 
          "An entry (row) represents a remote initiator currently 
          attached to a particular local target port of a particular 
          target device of a particular SCSI instance." 
     INDEX { scsiInstIndex, scsiDeviceIndex, scsiPortIndex, 
     scsiAttIntrPrtIdx } 
     ::= { scsiAttIntrPrtTable 1 } 
    
   ScsiAttIntrPrtEntry ::= SEQUENCE { 
     scsiAttIntrPrtIdx             ScsiIndexValue, 
     scsiAttIntrPrtAuthIntrIdx     ScsiIndexValueOrZero, 
     scsiAttIntrPrtName            ScsiName, 
     scsiAttIntrPrtId              ScsiIdentifier 
       } 
    
   scsiAttIntrPrtIdx OBJECT-TYPE 
     SYNTAX         ScsiIndexValue 
     MAX-ACCESS     not-accessible 
     STATUS         current 
     DESCRIPTION 
          " This object represents an arbitrary integer used to 
          uniquely identify a particular attached remote initiator port 
          to a particular target port within a particular SCSI target 
          device within a particular SCSI instance." 
     ::= { scsiAttIntrPrtEntry 1 } 
    
   scsiAttIntrPrtAuthIntrIdx OBJECT-TYPE 
     SYNTAX         ScsiIndexValueOrZero 
     MAX-ACCESS     read-only 
     STATUS         current 
     DESCRIPTION 
          "This object is the corresponding index in the 
          scsiAuthorizedIntrTable for this current attached remote 
          initiator or zero if this remote attached initiator is not 
          configured in that table." 
     ::= { scsiAttIntrPrtEntry 2 } 
    
   scsiAttIntrPrtName OBJECT-TYPE 
     SYNTAX         ScsiName 
     MAX-ACCESS     read-only 
     STATUS         current 
     DESCRIPTION 
 
          " This object represents the name of the remote initiator 
          attached to this local target port." 
     ::= { scsiAttIntrPrtEntry 3 } 
    
   scsiAttIntrPrtId OBJECT-TYPE 
     SYNTAX         ScsiIdentifier 
     MAX-ACCESS     read-only 
     STATUS         current 
     DESCRIPTION 
          " This object represents the identifier of the remote 
          initiator attached to this local target port." 
     ::= { scsiAttIntrPrtEntry 4 } 
    
    
   ------------------- Managed Objects regarding logical units -------- 
   scsiLuTable OBJECT-TYPE 
     SYNTAX         SEQUENCE OF ScsiLuEntry 
     MAX-ACCESS     not-accessible 
     STATUS         current 
     DESCRIPTION 
          " This table contains all the logical units exposed by local 
          target devices." 
     ::= { scsiLogicalUnit 1 } 
    
   scsiLuEntry OBJECT-TYPE 
     SYNTAX           ScsiLuEntry 
     MAX-ACCESS       not-accessible 
     STATUS           current 
     DESCRIPTION 
          "An entry (row) contains information applicable to a 
          particular logical unit of a particular local target device 
          within a particular SCSI instance. " 
     INDEX { scsiInstIndex, scsiDeviceIndex, scsiLuIndex} 
     ::= { scsiLuTable 1 } 
    
   ScsiLuEntry ::= SEQUENCE { 
     scsiLuIndex              ScsiIndexValue, 
     scsiLuDefaultLun         ScsiLUNOrZero, 
     scsiLuWwnName            ScsiNameIdOrZero, 
     scsiLuVendorId           SnmpAdminString, 
     scsiLuProductId          SnmpAdminString, 
     scsiLuRevisionId         SnmpAdminString, 
     scsiLuPeripheralType     Unsigned32, 
     scsiLuStatus             INTEGER, 
     scsiLuState              BITS, 
     scsiLuInCommands         Counter32, 
     scsiLuReadMegaBytes      Counter32, 
     scsiLuWrittenMegaBytes   Counter32, 
     scsiLuInResets           Counter32, 
     scsiLuOutQueueFullStatus Counter32, 
     scsiLuHSInCommands       Counter64 
   } 
    
 
   scsiLuIndex OBJECT-TYPE 
     SYNTAX         ScsiIndexValue 
     MAX-ACCESS     not-accessible 
     STATUS         current 
     DESCRIPTION 
          " This object represents an arbitrary integer used to 
          uniquely identify a particular logical unit within a 
          particular SCSI target device within a particular SCSI 
          instance." 
     ::= { scsiLuEntry 1 } 
    
   scsiLuDefaultLun OBJECT-TYPE 
     SYNTAX         ScsiLUNOrZero 
     MAX-ACCESS     read-only 
     STATUS         current 
     DESCRIPTION 
          " This object represents the default Logical Unit Number 
          (LUN) for this logical unit; it is the LUN that will appear 
          to an initiator that was not configured to see another LUN.  
          Note that this object will have a zero-length string if this 
          Logical Unit does not have a default LUN." 
     ::= { scsiLuEntry 2 } 
    
   scsiLuWwnName OBJECT-TYPE 
     SYNTAX         ScsiNameIdOrZero 
     MAX-ACCESS     read-only 
     STATUS         current 
     DESCRIPTION 
          " This object represents the World-Wide Name of this LU. 
          A value of zero has no meaning in this case." 
     ::= { scsiLuEntry 3 } 
    
   scsiLuVendorId   OBJECT-TYPE 
     SYNTAX         SnmpAdminString(SIZE(0..79)) 
     MAX-ACCESS     read-only 
     STATUS         current 
     DESCRIPTION 
          " This object represents a string identifying the vendor of 
          this LU according to the value in SCSI device page." 
     ::= { scsiLuEntry 4 } 
    
   scsiLuProductId  OBJECT-TYPE 
     SYNTAX         SnmpAdminString(SIZE(0..79)) 
     MAX-ACCESS     read-only 
     STATUS         current 
     DESCRIPTION 
          " This object represents a string identifying the product for 
          this LU according to the value in SCSI device page." 
     ::= { scsiLuEntry 5 } 
    
   scsiLuRevisionId OBJECT-TYPE 
     SYNTAX         SnmpAdminString(SIZE(0..79)) 
     MAX-ACCESS     read-only 
 
     STATUS         current 
     DESCRIPTION 
          "This object represents a string defining the product 
          revision of this LU according to the value in SCSI device 
          page." 
     ::= { scsiLuEntry 6 } 
    
   scsiLuPeripheralType  OBJECT-TYPE 
     SYNTAX         Unsigned32 
     MAX-ACCESS     read-only 
     STATUS         current 
     DESCRIPTION 
          "This object is the value returned to SCSI query VPD page 83. 
          It can be: direct-access device, sequential-access device, 
          printer, communication device and so on.  
          The values that can be returned here are defined in SCSI 
          Primary Commands -2." 
     REFERENCE  
          " ANSI - SCSI Primary Commands - 2 (SPC-2), T10 Project 1236-
          D, Revision 20, 18 July 2001  [16]" 
     ::= { scsiLuEntry 7 } 
    
   scsiLuStatus     OBJECT-TYPE 
     SYNTAX         INTEGER { 
               unknown(1), 
               available(2), 
               notAvailable(3), 
               broken(4), 
               readying(5), 
               abnormal(6) 
          } 
     MAX-ACCESS     read-only 
     STATUS         current 
     DESCRIPTION 
          " This object represents the status of this logical unit: 
          - unknown(1): The status of this logical unit cannot be 
          determined. 
          - available(2): The logical unit is fully operational (i.e., 
          accepts media access SCSI commands and has no state 
          information to report). 
          - notAvailable(3): The logical unit is capable of being 
          supported but not available (i.e., no logical unit is 
          currently present or the logical unit is present but not 
          configured for use). 
          - broken(4): The logical unit has failed and cannot respond 
          to SCSI commands. 
          - readying(5): The logical unit is being initialized and 
          access is temporarily limited. 
          - abnormal(6): The logical unit has state information 
          available that indicates it is operating with limits. The 
          scsiLuState indicates what those limits are. 
     " 
     REFERENCE  
 
          " SCSI Controller Commands-2 (SCC-2) standard NCITS.318-1998 
          6.3.1.8 REPORT STATES service action" 
     ::= { scsiLuEntry 8 } 
    
   scsiLuState OBJECT-TYPE 
     SYNTAX         BITS { 
               dataLost(0), 
               dynamicReconfigurationInProgress(1), 
               exposed(2), 
               fractionallyExposed(3), 
               partiallyExposed(4), 
               protectedRebuild(5), 
               protectionDisabled(6), 
               rebuild(7), 
               recalculate(8), 
               spareInUse(9), 
               verifyInProgress(10) 
          }  
     MAX-ACCESS     read-only 
     STATUS         current 
     DESCRIPTION 
          " This object represents the state of a logical unit and its 
          meaning is according the bit position: 
          0    Data lost: Within the logical unit data has been lost. 
          1    Dynamic reconfiguration in progress: The logical unit is 
               being reconfigured. In this state all data is still 
               protected. 
          2    Exposed: Within the logical unit data is not protected. 
               In this state all data is still valid, however, loss of 
               data/data-availability is unavoidable in the event of a 
               failure. 
          3    Fractionally exposed: Within the logical unit part of 
               the data is not protected. In this state all data is 
               still valid, however, a failure may cause a loss of data 
               or a loss of data availability. 
          4    Partially exposed: Within the logical unit one or more 
               underlying storage devices have failed. In this state 
               all data is still protected. 
          5    Protected rebuild: The logical unit is in the process of 
               a rebuild operation. In this state all data is 
               protected. 
          6    Protection disabled: Within the logical unit the data 
               protection method has been disabled. 
               In this state all data is still valid, however, however, 
               loss of data/data-availability is unavoidable in the 
               event of a failure. 
          7    Rebuild: The data protection method is in the process of 
               rebuilding data. In this state data is not protected. 
          8    Recalculate: The logical unit is in the process of a 
               recalculate operation. 
          9    Spare in use: Within the logical unit a storage device 
               in full or part being used to store data. In this state 
               all data is still protected. 
 
          10   Verify in progress: Within the logical unit data is 
               being verified." 
     REFERENCE  
          " SCSI Controller Commands-2 (SCC-2) standard NCITS.318-1998 
          6.3.1.8 REPORT STATES service action" 
     ::= { scsiLuEntry 9 } 
    
   scsiLuInCommands OBJECT-TYPE 
     SYNTAX         Counter32 
     UNITS          "commands" 
     MAX-ACCESS     read-only 
     STATUS         current 
     DESCRIPTION 
          " This object represents the number of commands received by 
          this logical unit." 
     ::= { scsiLuEntry 10 } 
      
   scsiLuReadMegaBytes OBJECT-TYPE 
     SYNTAX         Counter32 
     UNITS          "Megabytes" 
     MAX-ACCESS     read-only 
     STATUS         current 
     DESCRIPTION 
          " This object represents the amount of data in Megabytes read 
          from this logical unit." 
     ::= { scsiLuEntry 11 } 
    
   scsiLuWrittenMegaBytes OBJECT-TYPE 
     SYNTAX         Counter32 
     UNITS          "Megabytes" 
     MAX-ACCESS     read-only 
     STATUS         current 
     DESCRIPTION 
          " This object represents the amount of data in Megabytes 
          written by this logical unit." 
     ::= { scsiLuEntry 12 } 
    
   scsiLuInResets OBJECT-TYPE 
     SYNTAX         Counter32 
     UNITS          "resets" 
     MAX-ACCESS     read-only 
     STATUS         current 
     DESCRIPTION 
          " This object represents the number of resets received by 
          this logical unit." 
     ::= { scsiLuEntry 13 } 
           
    
   scsiLuOutQueueFullStatus   OBJECT-TYPE 
     SYNTAX         Counter32 
     MAX-ACCESS     read-only 
     STATUS         current 
     DESCRIPTION 
 
          " This object represents the number of queue full statuses 
          received by this logical unit." 
     ::= { scsiLuEntry 14 } 
    
   scsiLuHSInCommands OBJECT-TYPE 
     SYNTAX         Counter64 
     UNITS          "commands" 
     MAX-ACCESS     read-only 
     STATUS         current 
     DESCRIPTION 
          " This object represents the number of commands received by 
          this logical unit. This object provides support for systems 
          that can quickly generate lots of commands because they run 
          at high speed." 
     ::= { scsiLuEntry 15 } 
    
   ----------------------- Logical Unit Identifier Table --------------
           
   scsiLuIdTable OBJECT-TYPE 
     SYNTAX  SEQUENCE OF ScsiLuIdEntry 
     MAX-ACCESS       not-accessible 
     STATUS           current 
     DESCRIPTION 
          "A table of identifiers for all logical units exposed by 
          local targets device." 
     ::= { scsiLogicalUnit 2 } 
    
   scsiLuIdEntry OBJECT-TYPE 
     SYNTAX         ScsiLuIdEntry 
     MAX-ACCESS     not-accessible 
     STATUS         current 
     DESCRIPTION 
          "An entry (row) containing information applicable to a 
          particular identifier for a particular logical unit of a 
          particular target device within a particular SCSI instance. " 
     INDEX {scsiInstIndex, scsiDeviceIndex, scsiLuIndex, scsiLuIdIndex} 
     ::= { scsiLuIdTable 1 } 
    
   ScsiLuIdEntry ::= SEQUENCE { 
     scsiLuIdIndex       ScsiIndexValue, 
     scsiLuIdCodeSet     ScsiIdCodeSet, 
     scsiLuIdAssociation ScsiIdAssociation, 
     scsiLuIdType        ScsiIdType, 
     scsiLuIdValue       ScsiIdValue 
     } 
    
   scsiLuIdIndex    OBJECT-TYPE 
     SYNTAX          ScsiIndexValue 
     MAX-ACCESS      not-accessible 
     STATUS          current 
     DESCRIPTION 
          " This object represents an arbitrary integer used to 
          uniquely identify a particular LU Identifier within a 
 
          particular logical unit within a particular SCSI target 
          device within a particular SCSI instance." 
     ::= { scsiLuIdEntry 1 } 
    
   scsiLuIdCodeSet OBJECT-TYPE 
     SYNTAX           ScsiIdCodeSet  
     MAX-ACCESS       read-only 
     STATUS           current 
     DESCRIPTION 
          "This object specifies the code set in use with this 
          identifier. 
          The value is represented in the same format as is contained 
          in the identifier's Identification Descriptor within the 
          Logical Unit's Device Identification Page." 
     REFERENCE  
          " ANSI - SCSI Primary Commands - 2 ((SPC-2), Revision 20,   
          Chapter 8: section 8.4.4, page 210 Vital Product Data 
          Parameters [16]" 
     ::= { scsiLuIdEntry 2 } 
    
   scsiLuIdAssociation OBJECT-TYPE 
     SYNTAX           ScsiIdAssociation 
     MAX-ACCESS       read-only 
     STATUS           current 
     DESCRIPTION 
          "This object specifies what the identifier is associated with 
          (e.g, with the addressed physical/logical device or with a 
          particular port).  The value is represented in the same 
          format as is contained in the identifier's Identification 
          Descriptor within the Logical Unit's Device Identification 
          Page." 
     REFERENCE  
          " ANSI - SCSI Primary Commands - 2 (SPC-2), Revision 20, 
          Chapter 8: section 8.4.4, page 210 Vital Product Data 
          Parameters [16]" 
     ::= { scsiLuIdEntry 3 } 
    
   scsiLuIdType     OBJECT-TYPE 
     SYNTAX           ScsiIdType  
     MAX-ACCESS       read-only 
     STATUS           current 
     DESCRIPTION 
          "This object specifies the type of the identifier.  
          The value is represented in the same format as is contained 
          in the identifier's Identification Descriptor within the 
          Logical Unit's Device Identification Page." 
     REFERENCE  
          " ANSI - SCSI Primary Commands - 2 (SPC-2), Revision 20, 
          Chapter 8: section 8.4.4, page 210 Vital Product Data 
          Parameters  [16]" 
     ::= { scsiLuIdEntry 4 } 
    
   scsiLuIdValue OBJECT-TYPE 
 
     SYNTAX         ScsiIdValue 
     MAX-ACCESS     read-only 
     STATUS         current 
     DESCRIPTION 
          " This object represents the actual value of this identifier. 
          The format is defined by the objects scsiLuIdCodeSet, 
          scsiLuIdAssociation, scsiLuIdType. 
          The value is represented in the same format as is contained 
          in the identifier's Identification Descriptor within the 
          Logical Unit's Device Identification Page." 
     REFERENCE  
          " ANSI - SCSI Primary Commands - 2 (SPC-2), 
          Chapter 8: section 8.4.4, page 210 Vital Product Data 
     Parameters  [16]" 
   ::= { scsiLuIdEntry 5 } 
    
    
   ----------------------- The LUN Map Table -------------------------- 
    
   scsiLunMapTable OBJECT-TYPE 
     SYNTAX    SEQUENCE OF ScsiLunMapEntry 
     MAX-ACCESS     not-accessible 
     STATUS         current 
     DESCRIPTION 
          "This table includes LUNs additional to the default one. A 
          logical unit may have a different Logical Unit Number for 
          different initiators. This table provides a mapping between a 
          logical unit and a logical unit number." 
     ::= { scsiLogicalUnit 3 } 
    
   scsiLunMapEntry OBJECT-TYPE 
     SYNTAX          ScsiLunMapEntry 
     MAX-ACCESS      not-accessible 
     STATUS          current 
     DESCRIPTION 
       "An entry containing information about the mapping of a 
       particular Logical Unit to a particular LUN.  The set of 
       entries which all have the same values of scsiInstIndex, 
       scsiDeviceIndex and scsiLunMapIndex constitute a LUN Map within 
       a particular SCSI instance." 
     INDEX { scsiInstIndex, scsiDeviceIndex, scsiLunMapIndex, 
     scsiLunMapLun} 
     ::= { scsiLunMapTable 1 } 
    
   ScsiLunMapEntry ::= SEQUENCE { 
     scsiLunMapIndex     ScsiIndexValue, 
     scsiLunMapLun       ScsiLUNOrZero, 
     scsiLunMapLuIndex   ScsiIndexValue, 
     scsiLunMapRowStatus RowStatus 
     } 
    
   scsiLunMapIndex  OBJECT-TYPE 
     SYNTAX           ScsiIndexValue 
 
     MAX-ACCESS       not-accessible 
     STATUS           current 
     DESCRIPTION 
          " This object represents an arbitrary integer used to 
          uniquely identify a particular LunMap within a particular 
          SCSI target device within a particular SCSI instance." 
     ::= { scsiLunMapEntry 1 } 
    
   scsiLunMapLun    OBJECT-TYPE 
     SYNTAX           ScsiLUNOrZero 
     MAX-ACCESS       not-accessible 
     STATUS           current 
     DESCRIPTION 
          "This object specifies the Logical Unit Number, to which a 
          logical unit is mapped by this row. 
          A value of zero has no meaning in this case." 
     ::= { scsiLunMapEntry 2 } 
    
   scsiLunMapLuIndex OBJECT-TYPE 
     SYNTAX         ScsiIndexValue 
     MAX-ACCESS     read-create 
     STATUS         current 
     DESCRIPTION 
          "This object identifies the logical unit for which the value 
          of scsiLuIndex is the same as the value of this object.  The 
          identified logical unit is the one mapped to a LUN by this 
          row." 
     ::= { scsiLunMapEntry 3 } 
    
   scsiLunMapRowStatus   OBJECT-TYPE 
     SYNTAX          RowStatus 
     MAX-ACCESS      read-create 
     STATUS          current 
     DESCRIPTION 
          "This object allows an administrator to create and delete 
          this entry." 
     ::= { scsiLunMapEntry 4 } 
    
    
    
   -- Notifications 
   -- scsiNotifications OBJECT IDENTIFIER ::= { scsiModule 2 } 
   scsiNotificationsPrefix OBJECT IDENTIFIER  
     ::= { scsiNotifications 0 } 
    
   scsiTgtDeviceStatusChanged NOTIFICATION-TYPE 
     OBJECTS { scsiTgtDeviceStatus } 
     STATUS  current 
     DESCRIPTION 
          " A notification will be generated for each occurrence of the 
          abnormal status (e.g., if the SCSI target device's current 
          status is abnormal) providing that the SCSI instance's value 
          of scsiInstScsiNotificationsEnable is enabled. 
 
          An SNMP agent implementing the SCSI MIB should not send more 
          than three SCSI identical notifications in any 10-second 
          period." 
     ::= { scsiNotificationsPrefix 1 } 
    
   scsiLuStatusChanged NOTIFICATION-TYPE 
     OBJECTS { scsiLuStatus } 
     STATUS  current 
     DESCRIPTION 
          " A notification will be generated each time that 
          scsiLuStatus will change providing that the SCSI instance's 
          value of scsiInstScsiNotificationsEnable is enabled. 
          An SNMP agent implementing the SCSI MIB should not send more 
          than three SCSI identical notifications in any 10-second 
          period." 
     ::= { scsiNotificationsPrefix 2 } 
    
    
   -- The next part defines the conformance groups in use for SCSI MIB. 
   scsiCompliances OBJECT IDENTIFIER ::= { scsiConformance 1 } 
    
   scsiCompliance MODULE-COMPLIANCE 
     STATUS current 
     DESCRIPTION 
          "Describes the requirements for compliance to this SCSI MIB. 
          If an implementation can be both a target and an initiator, 
          all groups are mandatory." 
     MODULE  -- this module 
          MANDATORY-GROUPS { 
               scsiDeviceGroup                
                              } 
      
     OBJECT scsiInstAlias 
     MIN-ACCESS read-only 
     DESCRIPTION  
          "Write access is not mandatory." 
           
     OBJECT scsiInstScsiNotificationsEnable 
     MIN-ACCESS read-only 
     DESCRIPTION  
          "Write access is not mandatory." 
           
     OBJECT scsiDeviceAlias 
     MIN-ACCESS read-only 
     DESCRIPTION  
          "Write access is not mandatory." 
    
   -- Conditionally mandatory groups to be included with 
   -- the mandatory groups when the implementation has 
   -- SCSI target device. 
      
     GROUP scsiTargetGroup 
     DESCRIPTION 
 
          "This group is mandatory for all SCSI implementations that 
          have SCSI target devices." 
     GROUP scsiLunMapGroup 
     DESCRIPTION 
          "This group is mandatory for system having the capabilities 
          of mapping local targets and logical units according remote 
          initiators." 
    
     OBJECT scsiAuthIntrDevOrPort 
     MIN-ACCESS     read-only 
     DESCRIPTION  
          "Write access is not required." 
      
     OBJECT scsiAuthIntrName 
     MIN-ACCESS     read-only 
     DESCRIPTION  
          "Write access is not required." 
      
     OBJECT scsiAuthIntrLunMapIndex 
     MIN-ACCESS     read-only 
     DESCRIPTION  
          "Write access is not required." 
      
     OBJECT scsiAuthIntrRowStatus 
     SYNTAX RowStatus
     MIN-ACCESS read-only 
     DESCRIPTION  
          "Write access is not required, and only one of the six 
          enumerated values for the RowStatus textual convention need 
          be supported, specifically: active(1)."            
    
    
   -- Conditionally mandatory groups to be included with 
   -- the mandatory groups when the implementation has 
   -- SCSI initiator device. 
    
     GROUP scsiInitiatorGroup 
     DESCRIPTION 
          "This group is mandatory for all SCSI implementations that 
          have SCSI initiator devices." 
    
     OBJECT scsiIntrDevTgtAccessMode 
     MIN-ACCESS read-only 
     DESCRIPTION "Write access is not mandatory." 
    
     GROUP scsiDiscoveryGroup 
     DESCRIPTION 
          "This group is mandatory for system having the capabilities 
          of discovering remote targets via local initiators." 
    
     OBJECT scsiLunMapLuIndex 
     MIN-ACCESS read-only 
     DESCRIPTION  
 
          "Write access is not mandatory." 
           
     OBJECT scsiLunMapRowStatus 
     SYNTAX RowStatus
     MIN-ACCESS read-only 
     DESCRIPTION  
          "Write access is not required, and only one of the six 
          enumerated values for the RowStatus textual convention need 
          be supported, specifically: active(1)." 
           
     OBJECT scsiDscTgtDevOrPort 
     MIN-ACCESS read-only 
     DESCRIPTION  
          "Write access is not mandatory." 
           
     OBJECT scsiDscTgtName 
     MIN-ACCESS read-only 
     DESCRIPTION "Write access is not mandatory." 
    
     OBJECT scsiDscTgtConfigured  
     SYNTAX TruthValue
     MIN-ACCESS read-only 
     DESCRIPTION  
          "The value of true(1) is not mandatory neither the write 
          access." 
      
     OBJECT scsiDscTgtRowStatus 
     SYNTAX RowStatus
     MIN-ACCESS read-only 
     DESCRIPTION  
          "Write access is not required, and only one of the six 
          enumerated values for the RowStatus textual convention need 
          be supported, specifically: active(1)."            
    
   -- Conditionally mandatory groups to be included with the mandatory  
   -- groups when the implementation can gather statistics. 
     GROUP scsiDeviceStatGroup 
     DESCRIPTION 
          "This group is mandatory for all SCSI implementations that 
          can gather statistics." 
      
   -- Conditionally mandatory groups to be included with the mandatory  
   -- groups when the implementation can gather statistics at the SCSI 
   -- initiator side. 
     GROUP scsiInitiatorStatsGroup 
     DESCRIPTION 
          "This group is mandatory for all SCSI implementations that 
          can gather statistics at SCSI initiator side." 
     GROUP scsiDiscoveryStatsGroup 
     DESCRIPTION 
          "This group is mandatory for system having the capabilities 
          of gathering statistics regarding remote targets via local 
          initiators."    
 
    
   -- Conditionally mandatory groups to be included with the mandatory  
   -- groups when the implementation can gather statistics at the SCSI 
   -- target side. 
     GROUP scsiTargetStatsGroup 
     DESCRIPTION 
          "This group is mandatory for all SCSI implementations that 
          can gather statistics at SCSI target devices." 
     GROUP scsiLunMapStatsGroup 
     DESCRIPTION 
          "This group is mandatory for SCSI implementations able to map 
          local targets and logical units according remote initiators." 
    
   -- Conditionally mandatory groups to be included with the mandatory  
   -- groups when the implementation is running at high speed and can  
   -- gather statistics at the SCSI initiator side. 
     GROUP scsiInitiatorHSStatsGroup 
     DESCRIPTION 
          "This group is mandatory for all SCSI implementations that 
          can gather statistics at SCSI initiator side and are running 
          at high speed." 
     GROUP scsiDiscoveryHSStatsGroup 
     DESCRIPTION 
          "This group is mandatory for system having the capabilities 
          of gathering statistics regarding remote targets via local 
          initiators and are running at high speed."    
    
   -- Conditionally mandatory groups to be included with the mandatory  
   -- groups when the implementation  is running at high speed and can 
   -- gather statistics at the SCSI target side. 
     GROUP scsiTargetHSStatsGroup 
     DESCRIPTION 
          "This group is mandatory for all SCSI implementations that 
          can gather statistics at SCSI target devices in high speed 
          system." 
     GROUP scsiLunMapHSStatsGroup 
     DESCRIPTION 
          "This group is mandatory for SCSI implementations able to map 
          local targets and logical units according remote initiators 
          in high speed system." 
     ::= { scsiCompliances 1 } 
    
   scsiGroups OBJECT IDENTIFIER ::= { scsiConformance 2 } 
    
   scsiDeviceGroup OBJECT-GROUP 
     OBJECTS { 
          scsiInstAlias,  
          scsiInstSoftwareIndex,  
          scsiInstVendorVersion, 
          scsiInstScsiNotificationsEnable, 
          scsiDeviceAlias,              
          scsiDeviceRole,
          scsiDevicePortNumber, 
 
          scsiPortRole,  
          scsiPortTrnsptPtr, 
          scsiTrnsptType,  
          scsiTrnsptPointer,  
          scsiTrnsptDevName 
     } 
     STATUS current 
     DESCRIPTION 
          "A collection of objects providing information about SCSI 
          instances, devices and ports." 
     ::= { scsiGroups 1 } 
    
    
   scsiInitiatorGroup OBJECT-GROUP 
     OBJECTS { 
          scsiIntrDevTgtAccessMode, 
          scsiIntrPrtName,  
          scsiIntrPrtIdentifier, 
          scsiAttTgtPortDscTgtIdx, 
          scsiAttTgtPortName,  
          scsiAttTgtPortIdentifier 
     } 
     STATUS current 
     DESCRIPTION 
          "This group is relevant for an initiator device and port." 
     ::= { scsiGroups 2 } 
    
   scsiDiscoveryGroup OBJECT-GROUP 
     OBJECTS { 
          scsiDscTgtDevOrPort, 
          scsiDscTgtName,  
          scsiDscTgtConfigured,  
          scsiDscTgtDiscovered, 
          scsiDscTgtRowStatus, 
          scsiDscTgtLastCreation, 
          scsiDscLunLun, 
          scsiDscLunIdCodeSet, 
          scsiDscLunIdAssociation, 
          scsiDscLunIdType, 
          scsiDscLunIdValue 
     } 
     STATUS current 
     DESCRIPTION 
          "This group is relevant for the discovered targets by an 
          initiator port." 
     ::= { scsiGroups 3 } 
    
   scsiTargetGroup OBJECT-GROUP 
     OBJECTS { 
          scsiTgtDevNumberOfLUs, 
          scsiTgtDeviceStatus, 
          scsiTgtDevNonAccessibleLUs, 
          scsiTgtPortName, 
 
          scsiTgtPortIdentifier, 
          scsiAttIntrPrtAuthIntrIdx, 
          scsiAttIntrPrtName, 
          scsiAttIntrPrtId, 
          scsiLuDefaultLun, 
          scsiLuWwnName,  
          scsiLuVendorId,           
          scsiLuProductId,     
          scsiLuRevisionId, 
          scsiLuPeripheralType, 
          scsiLuStatus, 
          scsiLuState, 
          scsiLuIdCodeSet, 
          scsiLuIdAssociation, 
          scsiLuIdType, 
          scsiLuIdValue 
     } 
     STATUS current 
     DESCRIPTION 
          "This group is relevant for a target device and port." 
     ::= { scsiGroups 4 } 
    
    
   scsiLunMapGroup OBJECT-GROUP 
     OBJECTS { 
          scsiLunMapLuIndex,  
          scsiLunMapRowStatus, 
          scsiAuthIntrDevOrPort, 
          scsiAuthIntrName, 
          scsiAuthIntrLunMapIndex, 
          scsiAuthIntrLastCreation, 
          scsiAuthIntrRowStatus  
     } 
     STATUS current 
     DESCRIPTION          
          "This group is a collection of attributes regarding the 
          mapping between logical unit number, logical unit and target 
          device." 
     ::= { scsiGroups 5} 
    
   scsiTargetStatsGroup OBJECT-GROUP 
     OBJECTS { 
          scsiTgtPortInCommands, 
          scsiTgtPortWrittenMegaBytes, 
          scsiTgtPortReadMegaBytes, 
          scsiLuInCommands, 
          scsiLuReadMegaBytes, 
          scsiLuWrittenMegaBytes, 
          scsiLuInResets, 
          scsiLuOutQueueFullStatus 
     } 
     STATUS current 
     DESCRIPTION          
 
          "This group is a collection of statistics for all 
          implementations of the SCSI MIB that contain targets." 
     ::= { scsiGroups 6} 
    
   scsiTargetHSStatsGroup OBJECT-GROUP 
     OBJECTS { 
          scsiTgtPortHSInCommands, 
          scsiLuHSInCommands 
     } 
     STATUS current 
     DESCRIPTION          
          "This group is a collection of high speed statistics for all 
          implementations of the SCSI MIB that contain targets." 
     ::= { scsiGroups 7} 
    
   scsiLunMapStatsGroup OBJECT-GROUP 
     OBJECTS { 
          scsiAuthIntrAttachedTimes, 
          scsiAuthIntrOutCommands, 
          scsiAuthIntrReadMegaBytes, 
          scsiAuthIntrWrittenMegaBytes 
     } 
     STATUS current 
     DESCRIPTION          
          "This group is a collection of statistics regarding 
          initiators authorized to attach local logical unit and target 
          device." 
     ::= { scsiGroups 8} 
    
   scsiLunMapHSStatsGroup OBJECT-GROUP 
     OBJECTS { 
          scsiAuthIntrHSOutCommands   
     } 
     STATUS current 
     DESCRIPTION          
          "This group is a collection of high speed statistics 
          regarding initiators authorized to attach local logical unit 
          and target device." 
     ::= { scsiGroups 9} 
    
   scsiInitiatorStatsGroup OBJECT-GROUP 
     OBJECTS { 
          scsiIntrDevOutResets,  
          scsiIntrPrtOutCommands, 
          scsiIntrPrtWrittenMegaBytes, 
          scsiIntrPrtReadMegaBytes 
     } 
     STATUS current 
     DESCRIPTION          
          "This group is a collection of statistics for all 
          implementations of the SCSI MIB that contain initiators." 
     ::= { scsiGroups 10} 
    
 
   scsiInitiatorHSStatsGroup OBJECT-GROUP 
     OBJECTS { 
          scsiIntrPrtHSOutCommands 
     } 
     STATUS current 
     DESCRIPTION          
          "This group is a collection of high speed statistics for all 
          implementations of the SCSI MIB that contain initiators." 
     ::= { scsiGroups 11} 
    
   scsiDiscoveryStatsGroup OBJECT-GROUP 
     OBJECTS { 
          scsiDscTgtInCommands, 
          scsiDscTgtReadMegaBytes, 
          scsiDscTgtWrittenMegaBytes  
     } 
     STATUS current 
     DESCRIPTION          
          "This group is a collection of statistics for all 
          implementations of the SCSI MIB that contain discovered 
          initiators." 
     ::= { scsiGroups 12} 
    
   scsiDiscoveryHSStatsGroup OBJECT-GROUP 
     OBJECTS { 
          scsiDscTgtHSInCommands 
     } 
     STATUS current 
     DESCRIPTION          
       "This group is a collection of high speed statistics for all 
       implementations of the SCSI MIB that contain discovered 
       initiators." 
     ::= { scsiGroups 13} 
    
   scsiDeviceStatGroup OBJECT-GROUP 
     OBJECTS { 
          scsiDeviceResets,  
          scsiPortBusyStatuses  
     } 
     STATUS current 
     DESCRIPTION 
          "A collection of statistics regarding about SCSI devices and 
          ports." 
     ::= { scsiGroups 14 } 
    
   END 
    
